From: main@Radios.groups.io [mailto:main@Radios.groups.io] On Behalf Of Joe Murrin
Sent: Friday, March 5, 2021 18:55
To: main@radios.groups.io
Subject: Re: [Radios] GM300 problem

From: main@Radios.groups.io [mailto:main@Radios.groups.io] On Behalf Of Sudvia Traders & Co. Ltda.-
Sent: Wednesday, March 3, 2021 23:19
To: main@radios.groups.io
Subject: Re: [Radios] GM300 problem

Hi, I used to have a code plug for an I think it was 8 ch UHF GM300 handy.

It's been a long time since I used it or the radio as the programming was dos based.

If I can find it do you think it would be of any use to you?

---

From: main@Radios.groups.io <main@Radios.groups.io> on behalf of Todor <z31rm@...>
Sent: Monday, January 18, 2021 6:33 AM
To: main@Radios.groups.io <main@Radios.groups.io>
Subject: [Radios] GM300 problem

 

Hello all,

 

Accindentally I reprogrammed GM300 with wrong code plug.

Looks like this model was limited to less programms and I uploaded 16 programs into the radio .

Now , I can read content and there are 16 programs within but TX is inhibited .

Does anybody has good codeplug for this model:

 

FCCABZ99FT3030

TANAPA HUD3603A

Model M33GMC09CAA

s/n 159TYYF989

 

This is what I can read from it.

Codeplug witn only 4 program loc is good enough .

Thanks in advance.Regards,

 

Todor

 

 

 

Hello again,

This  GM300 was all working  with 4 channel prior to upload new content .

I made a mistake-saved original codeplug but later overwrited it with anothed content that appears to be not working.

And yes, it looks like 16 channel  capable – it has 2 digit display .

European model , too.

Will check again but working good code plug is welcome , anyway.

Of course , 16 channel type.

Regards,

Todor

The 9C says 16ch.

M mobile duh

3 10-25w

3 VHF

GM (it’s a GM300)

C 45.1meg if

0 12.5k narrowband RF

9C “Expanded Logic Board, 16 freq”

A who knows?

A I think this is American market.

So it should be fine with 16 channels and I’d be looking at where you went wrong in the codeplug. It’s been so long since I dealt with my UHF GM300 and VHF M120 that I can’t even find the codeplug files for them to test/check (likely on the OLD 486 MSDOS laptop). Are you using the DOS or radio doctor software?

Only other thing I can think of is a board swap and it’s NOT a 9C board in it.

------------------------------------------------------
------------------------------------------------------

Hello all,

Accindentally I reprogrammed GM300 with wrong code plug.

Looks like this model was limited to less programms and I uploaded 16 programs into the radio .

Now , I can read content and there are 16 programs within but TX is inhibited .

Does anybody has good codeplug for this model:

FCCABZ99FT3030

TANAPA HUD3603A

Model M33GMC09CAA

s/n 159TYYF989

This is what I can read from it.

Codeplug witn only 4 program loc is good enough .

Thanks in advance.Regards,

Todor

The 9C says 16ch.

M mobile duh

3 10-25w

3 VHF

GM (it’s a GM300)

C 45.1meg if

0 12.5k narrowband RF

9C “Expanded Logic Board, 16 freq”

A who knows?

A I think this is American market.

So it should be fine with 16 channels and I’d be looking at where you went wrong in the codeplug. It’s been so long since I dealt with my UHF GM300 and VHF M120 that I can’t even find the codeplug files for them to test/check (likely on the OLD 486 MSDOS laptop). Are you using the DOS or radio doctor software?

Only other thing I can think of is a board swap and it’s NOT a 9C board in it.

------------------------------------------------------
------------------------------------------------------

Hello all,

Accindentally I reprogrammed GM300 with wrong code plug.

Looks like this model was limited to less programms and I uploaded 16 programs into the radio .

Now , I can read content and there are 16 programs within but TX is inhibited .

Does anybody has good codeplug for this model:

FCCABZ99FT3030

TANAPA HUD3603A

Model M33GMC09CAA

s/n 159TYYF989

This is what I can read from it.

Codeplug witn only 4 program loc is good enough .

Thanks in advance.Regards,

Todor

Hello all,

Accindentally I reprogrammed GM300 with wrong code plug.

Looks like this model was limited to less programms and I uploaded 16 programs into the radio .

Now , I can read content and there are 16 programs within but TX is inhibited .

Does anybody has good codeplug for this model:

FCCABZ99FT3030

TANAPA HUD3603A

Model M33GMC09CAA

s/n 159TYYF989

This is what I can read from it.

Codeplug witn only 4 program loc is good enough .

Thanks in advance.Regards,

Todor

Hi there,

I did download from page group and I did run in win7 and I did what the “hints page”said, and no problem at all. I did use COM1, but there is no acknoweledge from radio. Any other tip to connected??

Many thanks in advance

73

 

 

Sent from Mail for Windows 10

 

From: Concetto Dovere
Sent: viernes, 13 de noviembre de 2020 13:19
To: main@radios.groups.io
Subject: Re: [Radios] Radio Doctor

 

I'm sending you (through google drive link) the GM300 software BUT it is for Xp system:

 

https://drive.google.com/file/d/1jcnss1EkrzA240z8IxqOjuolukef6hFX/view?usp=sharing

 

 

 

Il giorno gio 12 nov 2020 alle ore 04:55 Ken Pokigo <kdp101@...> ha scritto:

Where can I get the GM300 radio doctor software to download?

Thanks

 

Sent from Mail for Windows 10

 

--

Clausola di Riservatezza
Le informazioni contenute in questo messaggio di posta elettronica sono riservate e confidenziali e ne è vietata la diffusione in qualunque modo eseguita. Qualora Lei non fosse la persona a cui il presente messaggio è destinato, La invitiamo gentilmente ad eliminarlo dopo averne dato tempestiva comunicazione al mittente e a non utilizzare in alcun caso il suo contenuto.
Qualsivoglia utilizzo non autorizzato di questo messaggio e dei suoi eventuali allegati espone il responsabile alle relative conseguenze civili e penali.