GM300 problem
|
Todor
Hello all,
Accindentally I reprogrammed GM300 with wrong code plug. Looks like this model was limited to less programms and I uploaded 16 programs into the radio . Now , I can read content and there are 16 programs within but TX is inhibited . Does anybody has good codeplug for this model:
FCCABZ99FT3030 TANAPA HUD3603A Model M33GMC09CAA s/n 159TYYF989
This is what I can read from it. Codeplug witn only 4 program loc is good enough . Thanks in advance.Regards,
Todor
|
|
|
|
Glen O'Riley
The 9C says 16ch.
M mobile duh 3 10-25w 3 VHF GM (it’s a GM300) C 45.1meg if 0 12.5k narrowband RF 9C “Expanded Logic Board, 16 freq” A who knows? A I think this is American market.
So it should be fine with 16 channels and I’d be looking at where you went wrong in the codeplug. It’s been so long since I dealt with
my UHF GM300 and VHF M120 that I can’t even find the codeplug files for them to test/check (likely on the OLD 486 MSDOS laptop). Are you using the DOS or radio doctor software?
------------------------------------------------------
From: main@Radios.groups.io <main@Radios.groups.io>
On Behalf Of Todor via groups.io
Sent: Monday, 18 January 2021 10:33 PM To: main@Radios.groups.io Subject: [Radios] GM300 problem
Hello all,
Accindentally I reprogrammed GM300 with wrong code plug. Looks like this model was limited to less programms and I uploaded 16 programs into the radio . Now , I can read content and there are 16 programs within but TX is inhibited . Does anybody has good codeplug for this model:
FCCABZ99FT3030 TANAPA HUD3603A Model M33GMC09CAA s/n 159TYYF989
This is what I can read from it. Codeplug witn only 4 program loc is good enough . Thanks in advance.Regards,
Todor
|
|
|
|
Todor
Hello again,
This GM300 was all working with 4 channel prior to upload new content . I made a mistake-saved original codeplug but later overwrited it with anothed content that appears to be not working. And yes, it looks like 16 channel capable – it has 2 digit display . European model , too. Will check again but working good code plug is welcome , anyway. Of course , 16 channel type.
Regards, Todor
From: main@Radios.groups.io [mailto:main@Radios.groups.io] On Behalf Of Glen O'Riley via groups.io
Sent: Monday, January 18, 2021 12:47 To: main@Radios.groups.io Subject: Re: [Radios] GM300 problem
The 9C says 16ch.
M mobile duh 3 10-25w 3 VHF GM (it’s a GM300) C 45.1meg if 0 12.5k narrowband RF 9C “Expanded Logic Board, 16 freq” A who knows? A I think this is American market.
So it should be fine with 16 channels and I’d be looking at where you went wrong in the codeplug. It’s been so long since I dealt with my UHF GM300 and VHF M120 that I can’t even find the codeplug files for them to test/check (likely on the OLD 486 MSDOS laptop). Are you using the DOS or radio doctor software?
------------------------------------------------------ From: main@Radios.groups.io <main@Radios.groups.io> On Behalf Of Todor via groups.io
Hello all,
Accindentally I reprogrammed GM300 with wrong code plug. Looks like this model was limited to less programms and I uploaded 16 programs into the radio . Now , I can read content and there are 16 programs within but TX is inhibited . Does anybody has good codeplug for this model:
FCCABZ99FT3030 TANAPA HUD3603A Model M33GMC09CAA s/n 159TYYF989
This is what I can read from it. Codeplug witn only 4 program loc is good enough . Thanks in advance.Regards,
Todor
|
|
|
|
Glen O'Riley
I can’t help with a working codeplug but if you throw yours somewhere to take a look at (make a copy and change the frequencies if
you need then some of us could possibly take a look and see if we see anything different.
------------------------------------------------------
From: main@Radios.groups.io <main@Radios.groups.io>
On Behalf Of Todor via groups.io
Sent: Tuesday, 19 January 2021 6:45 AM To: main@Radios.groups.io Subject: Re: [Radios] GM300 problem
Hello again,
This GM300 was all working with 4 channel prior to upload new content . I made a mistake-saved original codeplug but later overwrited it with anothed content that appears to be not working. And yes, it looks like 16 channel capable – it has 2 digit display . European model , too. Will check again but working good code plug is welcome , anyway. Of course , 16 channel type.
Regards, Todor
From:
main@Radios.groups.io [mailto:main@Radios.groups.io]
On Behalf Of Glen O'Riley via groups.io
The 9C says 16ch.
M mobile duh 3 10-25w 3 VHF GM (it’s a GM300) C 45.1meg if 0 12.5k narrowband RF 9C “Expanded Logic Board, 16 freq” A who knows? A I think this is American market.
So it should be fine with 16 channels and I’d be looking at where you went wrong in the codeplug. It’s been so long since I dealt with my UHF GM300 and VHF M120
that I can’t even find the codeplug files for them to test/check (likely on the OLD 486 MSDOS laptop). Are you using the DOS or radio doctor software?
------------------------------------------------------ From:
main@Radios.groups.io <main@Radios.groups.io>
On Behalf Of Todor via groups.io
Hello all,
Accindentally I reprogrammed GM300 with wrong code plug. Looks like this model was limited to less programms and I uploaded 16 programs into the radio . Now , I can read content and there are 16 programs within but TX is inhibited . Does anybody has good codeplug for this model:
FCCABZ99FT3030 TANAPA HUD3603A Model M33GMC09CAA s/n 159TYYF989
This is what I can read from it. Codeplug witn only 4 program loc is good enough . Thanks in advance.Regards,
Todor
|
|
|
|
Andy KB1UIF
Hi, I used to have a code plug for an I think it was 8 ch UHF GM300 handy.
It's been a long time since I used it or the radio as the programming was dos based.
If I can find it do you think it would be of any use to you?
From: main@Radios.groups.io <main@Radios.groups.io> on behalf of Todor <z31rm@...>
Sent: Monday, January 18, 2021 6:33 AM To: main@Radios.groups.io <main@Radios.groups.io> Subject: [Radios] GM300 problem Hello all,
Accindentally I reprogrammed GM300 with wrong code plug. Looks like this model was limited to less programms and I uploaded 16 programs into the radio . Now , I can read content and there are 16 programs within but TX is inhibited . Does anybody has good codeplug for this model:
FCCABZ99FT3030 TANAPA HUD3603A Model M33GMC09CAA s/n 159TYYF989
This is what I can read from it. Codeplug witn only 4 program loc is good enough . Thanks in advance.Regards,
Todor
|
|
|
|
Jaroslav Tichý
toggle quoted messageShow quoted text
|
|
|
|
Todor
Hi Andy!
TKS for reply. I am not sure if I could use codeplug for UHF model. Mine is VHF . Tjanks anyway! 73, Todor Z31RM
From: main@Radios.groups.io [mailto:main@Radios.groups.io] On Behalf Of Andy KB1UIF
Sent: Wednesday, March 3, 2021 21:22 To: main@Radios.groups.io Subject: Re: [Radios] GM300 problem
Hi, I used to have a code plug for an I think it was 8 ch UHF GM300 handy. It's been a long time since I used it or the radio as the programming was dos based. If I can find it do you think it would be of any use to you?
From: main@Radios.groups.io <main@Radios.groups.io> on behalf of Todor <z31rm@...>
Hello all,
Accindentally I reprogrammed GM300 with wrong code plug. Looks like this model was limited to less programms and I uploaded 16 programs into the radio . Now , I can read content and there are 16 programs within but TX is inhibited . Does anybody has good codeplug for this model:
FCCABZ99FT3030 TANAPA HUD3603A Model M33GMC09CAA s/n 159TYYF989
This is what I can read from it. Codeplug witn only 4 program loc is good enough . Thanks in advance.Regards,
Todor
|
|
|
|
Sudvia Traders & Co. Ltda.-
Hi Todor, Well, I had experienced same problem while ago. What I did, to clone with other GM300 and problem was solve. After that, you can write again with the right codeplug. 73’
El El mié, 3 de mar. de 2021 a la(s) 18:02, Todor <z31rm@...> escribió:
|
|
|
|
Berthold Edmund
Hi, The DOS program should be able to fix your need on this codeplug. Thanks Bert
On Thursday, March 4, 2021, 07:27:36 AM GMT+11, Andy KB1UIF <comexe1@...> wrote:
Hi, I used to have a code plug for an I think it was 8 ch UHF GM300 handy.
It's been a long time since I used it or the radio as the programming was dos based.
If I can find it do you think it would be of any use to you?
From: main@Radios.groups.io <main@Radios.groups.io> on behalf of Todor <z31rm@...>
Sent: Monday, January 18, 2021 6:33 AM To: main@Radios.groups.io <main@Radios.groups.io> Subject: [Radios] GM300 problem Hello all,
Accindentally I reprogrammed GM300 with wrong code plug. Looks like this model was limited to less programms and I uploaded 16 programs into the radio . Now , I can read content and there are 16 programs within but TX is inhibited . Does anybody has good codeplug for this model:
FCCABZ99FT3030 TANAPA HUD3603A Model M33GMC09CAA s/n 159TYYF989
This is what I can read from it. Codeplug witn only 4 program loc is good enough . Thanks in advance.Regards,
Todor
|
|
|
|
Todor
Good idea! Thanks a lot! Todor
From: main@Radios.groups.io [mailto:main@Radios.groups.io] On Behalf Of Sudvia Traders & Co. Ltda.-
Hi Todor, Well, I had experienced same problem while ago. What I did, to clone with other GM300 and problem was solve. After that, you can write again with the right codeplug. 73’
El El mié, 3 de mar. de 2021 a la(s) 18:02, Todor <z31rm@...> escribió:
|
|
|
|
Joe Murrin
I have a pair of GM300's setup as a GMRS repeater but don't currently have a system setup to read the code-plug. If you are local, I would be more than happy to share the codeplug in exchange for assistance in getting a system setup myself to read/write to the GM300's
On Wed, Mar 3, 2021 at 11:47 PM Todor <z31rm@...> wrote:
|
|
|
|
Todor
Hi!
So sorry , I am citizen of Macedonia. Good luck with your GM300!
Todor
From: main@Radios.groups.io [mailto:main@Radios.groups.io] On Behalf Of Joe Murrin
I have a pair of GM300's setup as a GMRS repeater but don't currently have a system setup to read the code-plug. If you are local, I would be more than happy to share the codeplug in exchange for assistance in getting a system setup myself to read/write to the GM300's
On Wed, Mar 3, 2021 at 11:47 PM Todor <z31rm@...> wrote:
|
|
|